Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 26240400 
Found #68 errors of type = ERROR qk -211 Tsys value for device i1 overflowed or was less than zero. 
Found #40 errors of type = ERROR st  -14 Antenna stuck.
 
Found #7 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #6 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #6 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #6 errors of type = ERROR ch   -4 Device vb timed-out on response from MATCN 
Found #4 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #4 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR ch -304 vb TPI selection does not check with requested setting 
Found #1 errors of type = ERROR ch -305 vb USB attenuator does not check with requested setting 
Found #1 errors of type = ERROR ch -302 vb frequency does not check with requested value 
Found #1 errors of type = ERROR ch -303 vb bandwidth does not check with requested value 
Found #1 errors of type = ERROR qd -301 Synch block CRC checksum test FAILED. 
Found #1 errors of type = ERROR ch -306 vb LSB attenuator does not check with requested setting 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these RX parameters: 02(LO) 03(DCAL) 0E(LO5MHZ)
RX1 min= 43.65 max= 45.48
RX2 min= 39.37 max= 40.84
RX3 min= 0.148 max= 0.151
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r4300ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 65.5 99.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 64.5 ymax 110.2 
in match_chan ft1= r4300ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 65.5 99.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 55.6 ymax 96.2 
in match_chan ft1= r4300ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 65.5 99.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 135.5 ymax 305