Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 16736400 
Found #276 errors of type = ERROR st -504 Az power supply failure
 
Found #22 errors of type = ERROR an   -7 Antenna communications restored. 
Found #21 errors of type = ERROR st  -14 Antenna stuck.
 
Found #14 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #12 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #9 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #9 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #4 errors of type = ERROR st -503 Az signal failure
 
Found #3 errors of type = ERROR st -502 Az communications error  bit should be 0
 
Found #2 errors of type = ERROR qk -211 Tsys value for device i1 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v1 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v2 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #2 errors of type = ERROR m5 -900 Already off 
Found #2 errors of type = ERROR qk -211 Tsys value for device v3 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v4 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #2 errors of type = ERROR m5 -906 MARK5 return code 6: inconsistent or conflicting request 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #1 errors of type = ERROR st -514 El power supply failure
 
Found #1 errors of type = ERROR st  -12 Antenna time-out.
 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these RX parameters: 02(LO) 03(DCAL) 0E(LO5MHZ)
RX1 min= 43.89 max= 2007.193.18:41:45.34
RX2 min= 39.37 max= 45.36
RX3 min= 0.152 max= 0.157
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r4284ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max -5 273.4
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 203.1 ymax 305 
in match_chan ft1= r4284ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max -5 273.4
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 220.4 ymax 293.2 
in match_chan ft1= r4284ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max -5 273.4
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 44.6 ymax 305