Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 11030400 
Found #585 errors of type = ERROR ch   -4 Device vb timed-out on response from MATCN 
Found #84 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #84 errors of type = ERROR ma   -4 Device vb timed-out on response. 
Found #16 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #8 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #4 errors of type = ERROR st  -14 Antenna stuck.
 
Found #4 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #4 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #3 errors of type = ERROR ib   -4 GPIB Device time-out on response ca 
Found #2 errors of type = ERROR ch -313 IF2 attenuator does not check with requested value 
Found #2 errors of type = ERROR ch -312 IF1 attenuator does not check with requested value 
Found #2 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #1 errors of type = ERROR ch -308 vd total power integrator overflow 
Found #1 errors of type = ERROR ch -308 ve total power integrator overflow 
Found #1 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #1 errors of type = ERROR ch -308 va total power integrator overflow 
Found #1 errors of type = ERROR ch -308 vc total power integrator overflow 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1275ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 0.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -4.9 ymax 305 
in match_chan ft1= r1275ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 0.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 216.8 ymax 305 
in match_chan ft1= r1275ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 0.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 90.5 ymax 305