Starting generation of Calibration File 
FS version = 0009.0009.0000 
time_zero = 4982400 
Found #1185 errors of type = ERROR st   -7 Antenna off-source! 
Found #745 errors of type = ERROR ma   -4 Device v4 timed-out on response. 
Found #733 errors of type = ERROR qk -211 Tsys value for device v4 overflowed or was less than zero. 
Found #490 errors of type = ERROR st   -4 Interface not set to remote. 
Found #301 errors of type = ERROR ch   -4 Device v4 timed-out on response from MATCN 
Found #138 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #138 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #33 errors of type = ERROR st -994 No new wx data since last report 
Found #6 errors of type = ERROR ch -309 v6 alarm is on 
Found #4 errors of type = ERROR un  115 Operation now in progress 
Found #4 errors of type = ERROR ch   -4 Device ve timed-out on response from MATCN 
Found #4 errors of type = ERROR m5  -23 mk5cn: socket open error from getsockopt() 
Found #3 errors of type = ERROR ch -305 ve USB attenuator does not check with requested setting 
Found #3 errors of type = ERROR ch -302 ve frequency does not check with requested value 
Found #3 errors of type = ERROR ch -306 ve LSB attenuator does not check with requested setting 
Found #3 errors of type = ERROR ch -306 v4 LSB attenuator does not check with requested setting 
Found #3 errors of type = ERROR ch -309 ve alarm is on 
Found #3 errors of type = ERROR ch -303 v4 bandwidth does not check with requested value 
Found #3 errors of type = ERROR ch -303 ve bandwidth does not check with requested value 
Found #3 errors of type = ERROR ch -309 v4 alarm is on 
Found #3 errors of type = ERROR ch -302 v4 frequency does not check with requested value 
Found #3 errors of type = ERROR ch -307 ve unlock indicator is on 
Found #3 errors of type = ERROR ch -304 v4 TPI selection does not check with requested setting 
Found #3 errors of type = ERROR ch -305 v4 USB attenuator does not check with requested setting 
Found #3 errors of type = ERROR ch -304 ve TPI selection does not check with requested setting 
Found #2 errors of type = ERROR ch -307 v4 unlock indicator is on 
Found #2 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #1 errors of type = ERROR st   -6 Antenna control restored. 
Found #1 errors of type = ERROR ch -302 v6 frequency does not check with requested value 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these SK parameters: 00(BXFNT) 02(LO_TMP) 03(DCAL_T)
RX1 min= 21.90 max= 2007.057.17:00:01.19
RX2 min= 47.90 max= 48.60
RX3 min= -180.7 max= 35.90
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1265ny.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 25.2 76.9
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 21.3 ymax 140.3 
in match_chan ft1= r1265ny.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 25.2 76.9
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 28.5 ymax 66 
in match_chan ft1= r1265ny.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 25.2 76.9
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 21.2 ymax 39.2