Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 2556000 
Found #195 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #40 errors of type = ERROR an  -11 An antenna SYPARM routine failed. 
Found #23 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #22 errors of type = ERROR an  -10 A control SYPARM routine failed. 
Found #22 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #9 errors of type = ERROR qk -211 Tsys value for device v2 overflowed or was less than zero. 
Found #6 errors of type = ERROR qk -211 Tsys value for device v4 overflowed or was less than zero. 
Found #6 errors of type = ERROR qk -211 Tsys value for device v6 overflowed or was less than zero. 
Found #6 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #5 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #5 errors of type = ERROR qk -211 Tsys value for device v3 overflowed or was less than zero. 
Found #5 errors of type = ERROR qk -211 Tsys value for device v5 overflowed or was less than zero. 
Found #5 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device i3 overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device v1 overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device i1 overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device v8 overflowed or was less than zero. 
Found #3 errors of type = ERROR ch -309 v4 alarm is on 
Found #2 errors of type = ERROR qk -211 Tsys value for device v7 overflowed or was less than zero. 
Found #1 errors of type = ERROR bo -173 Disk recording was commanded  either use disk_record off or terminate disk_record_ok. 
Found #1 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #1 errors of type = ERROR ch -301 v4 module is not in remote 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1261hh.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 49.2 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 60.3 ymax 305 
in match_chan ft1= r1261hh.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 49.2 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 42.9 ymax 305 
in match_chan ft1= r1261hh.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 49.2 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 42.6 ymax 305