Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 1530000 
Found #158 errors of type = ERROR qk -211 Tsys value for device i3 overflowed or was less than zero. 
Found #32 errors of type = ERROR ch -308 vc total power integrator overflow 
Found #19 errors of type = ERROR st  -14 Antenna stuck.
 
Found #17 errors of type = ERROR ch -308 vd total power integrator overflow 
Found #17 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #10 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #9 errors of type = ERROR ch -308 v3 total power integrator overflow 
Found #6 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #4 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #4 errors of type = ERROR qk -211 Tsys value for device v3 overflowed or was less than zero. 
Found #3 errors of type = ERROR ch -370 Total power integrator overflow on IF3 
Found #3 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #3 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #2 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR ch -309 v4 alarm is on 
Found #1 errors of type = ERROR m5 -900 Check formatter serial number even 
Found #1 errors of type = ERROR an   -7 Antenna communications restored. 
Found #1 errors of type = ERROR qd -301 Synch block CRC checksum test FAILED. 
Found #1 errors of type = ERROR m5 -906 MARK5 return code 6: inconsistent or conflicting request 
Found #1 errors of type = ERROR st -503 Az signal failure
 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these RX parameters: 02(LO) 03(DCAL) 0E(LO5MHZ)
RX1 min= 44.75 max= 46.33
RX2 min= 39.86 max= 41.08
RX3 min= 0.150 max= 0.152
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= crms01ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 64.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 58.8 ymax 160.5 
in match_chan ft1= crms01ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 64.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 59.7 ymax 162.5 
in match_chan ft1= crms01ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 64.5 305
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 28.5 ymax 305