Starting generation of Calibration File 
FS version = 0009.0007.0000 
time_zero = 10249200 
Found #538 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #18 errors of type = ERROR ma   -4 Device t1 timed-out on response. 
Found #18 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #18 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #16 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #16 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #16 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #16 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #12 errors of type = ERROR ma   -4 Device h1 timed-out on response. 
Found #9 errors of type = ERROR ch -308 vc total power integrator overflow 
Found #7 errors of type = ERROR ch -309 v9 alarm is on 
Found #6 errors of type = ERROR qi -302 Last commanded IFD attenuations used as default  please modify command. 
Found #6 errors of type = ERROR q+ -302 Last commanded IF3 attenuation used as default  please modify command. 
Found #5 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #4 errors of type = ERROR st -403 no response from time counter server 
Found #3 errors of type = ERROR st -100 invalid time in antenna message - antenna protocol error. 
Found #2 errors of type = ERROR fp  -20 Did not reach source in allotted time 
Found #2 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #1 errors of type = ERROR st -100 wrong OK STOP message - antenna protocol error. 
Found #1 errors of type = ERROR fp -100 Couldn't get back to source after an error 
Found #1 errors of type = ERROR ch -308 va total power integrator overflow 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r4171sv.log.tsy1.ntup nt1= 7 st1= 1u tt= 1
set scale tsys1 [2] min max 7.8 58.0
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 0.0999999999999996 ymax 57.1 
in match_chan ft1= r4171sv.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 7.8 58.0
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 3.3 ymax 117 
in match_chan ft1= r4171sv.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 7.8 58.0
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 42 ymax 305