Starting generation of Calibration File 
FS version = 0009.0007.0000 
time_zero = 9378000 
Found #461 errors of type = ERROR AN   -4 Interface not set to remote. 
Found #379 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #17 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #6 errors of type = ERROR ma   -4 Device t1 timed-out on response. 
Found #6 errors of type = ERROR st -100 wrong OK STOP message - antenna protocol error. 
Found #5 errors of type = ERROR ch -308 vc total power integrator overflow 
Found #5 errors of type = ERROR ch -308 va total power integrator overflow 
Found #4 errors of type = ERROR ma   -4 Device h1 timed-out on response. 
Found #2 errors of type = ERROR q+ -302 Last commanded IF3 attenuation used as default  please modify command. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #2 errors of type = ERROR qi -302 Last commanded IFD attenuations used as default  please modify command. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vb overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device i1 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #1 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR ch -302 v6 frequency does not check with requested value 
Found #1 errors of type = ERROR st -100 invalid time in antenna message - antenna protocol error. 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1171sv.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 28.0 38.8
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 22.6 ymax 56.5 
in match_chan ft1= r1171sv.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 28.0 38.8
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 38.2 ymax 69.5 
in match_chan ft1= r1171sv.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 28.0 38.8
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 55.8 ymax 305