Starting generation of Calibration File 
FS version = 0009.0004.0005 
time_zero = 6346800 
Rack type is VLBA
Found #317 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #317 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #26 errors of type = ERROR qg -303 Track 33 parity errors exceed threshold. 
Found #14 errors of type = ERROR qg -303 Track 32 parity errors exceed threshold. 
Found #12 errors of type = ERROR qg -304 Track 33 sync errors exceed threshold. 
Found #8 errors of type = ERROR qg -303 Track  9 parity errors exceed threshold. 
Found #7 errors of type = ERROR qg -303 Track 29 parity errors exceed threshold. 
Found #7 errors of type = ERROR qg -303 Track  5 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track  8 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track 17 parity errors exceed threshold. 
Found #3 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #3 errors of type = ERROR qk -211 Tsys value for device bu overflowed or were less than zero. 
Found #2 errors of type = ERROR st   -7 Antenna off-source! 
Found #2 errors of type = ERROR qg -303 Track 31 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -303 Track 13 parity errors exceed threshold. 
Found #2 errors of type = ERROR st   -5 Error return from antenna. 
Found #1 errors of type = ERROR ch -208 b7 gain mode does not check with requested setting 
Found #1 errors of type = ERROR mc   -5 Interface fm failed to handshake on monitor. 
Found #1 errors of type = ERROR qg -303 Track  6 parity errors exceed threshold. 
Found #1 errors of type = ERROR st   -6 Antenna control restored. 
Found #1 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #1 errors of type = ERROR mc   -2 Interface b7 responded  but did not ACKnowledge. 
Found #1 errors of type = ERROR qg -303 Track 16 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device cu overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track 20 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -303 Track 30 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -303 Track  2 parity errors exceed threshold. 
Found #1 errors of type = ERROR st   -4 Interface not set to remote. 
Found #1 errors of type = ERROR qg -303 Track  3 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -303 Track 25 parity errors exceed threshold. 
Found #1 errors of type = ERROR ch -233 rc tape drive should be moving and it isn't 
Found these BBCs: bbc06 bbc11 
NBBC: 2
Found these SX parameters: slo xlo sup
RX1 min= 3.82 max= 2000.073.11:50:54.32
RX2 min= 4.62 max= 4.64
RX3 min= 260.38 max= 272.59
Plotting 2 Tsys channels: 06 11 
Tsysa values are: 1 2 3 etc
Tsysb values are:  10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 2
in match_chan ft1= rdv20kk.log.tsy1.ntup nt1= 12 st1= 6u tt= 1
set scale tsys1 [2] min max 31.3 82.0
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 25.1 ymax 86.3 
in match_chan ft1= rdv20kk.log.tsy2.ntup nt1= 9 st1= 11u tt= 2
set scale tsys1 [2] min max 31.3 82.0
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305