Starting generation of Calibration File 
FS version = 0009.0004.0013 
time_zero = 16218000 
Rack type is VLBA
Rack type is VLBA
Found #52 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #52 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #18 errors of type = ERROR st   -4 Interface not set to remote. 
Found #17 errors of type = ERROR st   -7 Antenna off-source! 
Found #10 errors of type = ERROR qg -303 Track  8 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 22 parity errors exceed threshold. 
Found #8 errors of type = ERROR qg -303 Track 20 parity errors exceed threshold. 
Found #6 errors of type = ERROR qg -303 Track 28 parity errors exceed threshold. 
Found #6 errors of type = ERROR qg -303 Track 29 parity errors exceed threshold. 
Found #5 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track 11 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track 15 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 30 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 13 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 14 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track  7 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 10 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 18 parity errors exceed threshold. 
Found #3 errors of type = ERROR ch -239 rc tape drive should be recording but no groups are enabled. 
Found #2 errors of type = ERROR ch -233 rc tape drive should be moving and it isn't 
Found #1 errors of type = ERROR bo -211 Can't open a new schedule when an experiment procedure is executing 
Found #1 errors of type = ERROR qk -211 Tsys value for device au overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device cu overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track 21 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device eu overflowed or were less than zero. 
Found #1 errors of type = ERROR mc   -2 Interface ba responded  but did not ACKnowledge. 
Found #1 errors of type = ERROR st   -6 Antenna control restored. 
Found #1 errors of type = ERROR qk -211 Tsys value for device bu overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track  5 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -303 Track 25 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device du overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track 19 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 9u overflowed or were less than zero. 
Found these BBCs: bbc06 bbc11 bbc06
NBBC: 3
Found these SX parameters: slo xlo sup
RX1 min= 3.81 max= 2000.187.17:52:11.18
RX2 min= 4.62 max= 4.64
RX3 min= 262.34 max= 271.13
Plotting 3 Tsys channels: 06 11 06
Tsysa values are: 1 2 3 etc
Tsysb values are: 9 10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 3
in match_chan ft1= na375kk.log.tsy1.ntup nt1= 12 st1= 6u tt= 1
set scale tsys1 [2] min max 34.1 68.3
set scale tsys2 [2] min max -5 57.1
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 22.7 ymax 62 
in match_chan ft1= na375kk.log.tsy2.ntup nt1= 9 st1= 11u tt= 2
set scale tsys1 [2] min max 34.1 68.3
set scale tsys2 [2] min max -5 57.1
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 62.1 
in match_chan ft1= na375kk.log.tsy1.ntup nt1= 12 st1= 6u tt= 1
set scale tsys1 [2] min max 34.1 68.3
set scale tsys2 [2] min max -5 57.1
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 22.7 ymax 62