Starting generation of Calibration File 
FS version = 0009.0004.0006 
time_zero = 27514800 
Rack type is VLBA
Found #307 errors of type = ERROR qk -211 Tsys value for device ia overflowed or were less than zero. 
Found #307 errors of type = ERROR qk -211 Tsys value for device ic overflowed or were less than zero. 
Found #301 errors of type = ERROR ST   -2 portopen_: not able to open device 
Found #301 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #300 errors of type = ERROR st -434 Error reading FM offset port. (OFF the 50 Ohm at counter!) 
Found #14 errors of type = ERROR qo -410 BEAM size must already be defined. 
Found #11 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #10 errors of type = ERROR qg -303 Track 14 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track  6 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track 22 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track 30 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track 24 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track 18 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track 16 parity errors exceed threshold. 
Found #10 errors of type = ERROR qg -303 Track  4 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 31 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 13 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 23 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 15 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 25 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 17 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track  9 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 10 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track  7 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 19 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 29 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track  5 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 11 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 28 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track 21 parity errors exceed threshold. 
Found #9 errors of type = ERROR qg -303 Track  8 parity errors exceed threshold. 
Found #8 errors of type = ERROR qg -303 Track 20 parity errors exceed threshold. 
Found #8 errors of type = ERROR qg -303 Track 27 parity errors exceed threshold. 
Found #6 errors of type = ERROR qg -303 Track 12 parity errors exceed threshold. 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #2 errors of type = ERROR qo -401 No default for BEAMx  until LO has  been setup. 
Found #1 errors of type = ERROR ST -603 Weather station is sending parameters again. 
Found #1 errors of type = ERROR sc   -2 setcl: formatter time out-of-range 
Found #1 errors of type = ERROR ST -601 Weather station didn't send parameters. 
Found #1 errors of type = ERROR q  -201 Maximum of 12 characters in operator ID. 
Found #1 errors of type = ERROR ch -233 rc tape drive should be moving and it isn't 
Found these BBCs:   
NBBC: 0
Found these RX parameters: 00(BXFNT_) 01(IF_PLT) 03(DCAL_T)
RX1 min= 10.30 max= 23.10
RX2 min= 8.900 max= 21.90
RX3 min= 39.30 max= 43.50
Plotting 0 Tsys channels:   
Tsysa values are: 1 2 3 etc
Tsysb values are: 9 10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 0