Starting generation of Calibration File 
FS version = 0009.0004.0001 
time_zero = 910800 
Rack type is VLBA
Found #29 errors of type = ERROR qk -211 Tsys value for device ia overflowed or were less than zero. 
Found #8 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #8 errors of type = ERROR st   -1 Antenna got the wrong angles 
Found #7 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #4 errors of type = ERROR ch -208 b8 gain mode does not check with requested setting 
Found #4 errors of type = ERROR ma   -4 Device wx timed-out on response. 
Found #3 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #3 errors of type = ERROR ch   -4 Device rx timed-out on response from MATCN 
Found #2 errors of type = ERROR qk -211 Tsys value for device eu overflowed or were less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device 6u overflowed or were less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device 1u overflowed or were less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device cu overflowed or were less than zero. 
Found #2 errors of type = ERROR ma   -4 Device rx timed-out on response. 
Found #2 errors of type = ERROR st   -2 Commanding antenna failed too many times  giving up. 
Found #2 errors of type = ERROR qk -211 Tsys value for device ic overflowed or were less than zero. 
Found #1 errors of type = ERROR mc   -2 Interface ba responded  but did not ACKnowledge. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 5u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device bu overflowed or were less than zero. 
Found #1 errors of type = ERROR an -102 Pointing computer command angles are incorrect. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 2u overflowed or were less than zero. 
Found #1 errors of type = ERROR mc   -2 Interface b8 responded  but did not ACKnowledge. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 3u overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track 15 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 7u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 8u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 9u overflowed or were less than zero. 
Found #1 errors of type = ERROR st   -3 Commanding angles okay now. 
Found these BBCs: bbc02 bbc06 bbc11
NBBC: 3
Found these RX parameters: 00(front) 02(lo) 03(dcal)
RX1 min= 15.32 max= 2000.010.13:34:40.40
RX2 min= 44.26 max= 47.43
RX3 min= 44.50 max= 47.31
Plotting 3 Tsys channels: 02 06 11
Tsysa values are: 1 2 3 etc
Tsysb values are: 9 10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 3
in match_chan ft1= is146gc.log.tsy1.ntup nt1= 8 st1= 2u tt= 1
set scale tsys1 [2] min max 53.4 305
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305 
in match_chan ft1= is146gc.log.tsy1.ntup nt1= 12 st1= 6u tt= 1
set scale tsys1 [2] min max 53.4 305
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305 
in match_chan ft1= is146gc.log.tsy2.ntup nt1= 9 st1= 11u tt= 2
set scale tsys1 [2] min max 53.4 305
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305