Starting generation of Calibration File 
FS version = 0009.0004.0006 
time_zero = 11786400 
Rack type is VLBA
Found #244 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #244 errors of type = ERROR qk -211 Tsys value for device ic overflowed or were less than zero. 
Found #45 errors of type = ERROR ST   -2 portopen_: not able to open device 
Found #43 errors of type = ERROR st -434 Error reading FM offset port. (OFF the 50 Ohm at counter!) 
Found #9 errors of type = ERROR qo -410 BEAM size must already be defined. 
Found #7 errors of type = ERROR qk -211 Tsys value for device ia overflowed or were less than zero. 
Found #7 errors of type = ERROR qg -303 Track 22 parity errors exceed threshold. 
Found #7 errors of type = ERROR qg -303 Track 18 parity errors exceed threshold. 
Found #5 errors of type = ERROR qg -303 Track 15 parity errors exceed threshold. 
Found #5 errors of type = ERROR qg -303 Track 30 parity errors exceed threshold. 
Found #3 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #3 errors of type = ERROR qg -303 Track 14 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 10 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #2 errors of type = ERROR qo -401 No default for BEAMx  until LO has  been setup. 
Found #2 errors of type = ERROR ST -603 Weather station is sending parameters again. 
Found #2 errors of type = ERROR ST -601 Weather station didn't send parameters. 
Found #2 errors of type = ERROR qg -303 Track 11 parity errors exceed threshold. 
Found #2 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #1 errors of type = ERROR qk -211 Tsys value for device 8u overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track  5 parity errors exceed threshold. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 9u overflowed or were less than zero. 
Found #1 errors of type = ERROR vt -201 Tape parameter must be low  or off. 
Found #1 errors of type = ERROR sc   -2 setcl: formatter time out-of-range 
Found #1 errors of type = ERROR qk -211 Tsys value for device 7u overflowed or were less than zero. 
Found these BBCs: bbc02 bbc06 bbc11
NBBC: 3
Found these RX parameters: 00(BXFNT_) 01(IF_PLT) 03(DCAL_T)
RX1 min= 19.60 max= 34.10
RX2 min= 17.40 max= 31.90
RX3 min= 42.80 max= 44.90
Plotting 3 Tsys channels: 02 06 11
Tsysa values are: 1 2 3 etc
Tsysb values are: 9 10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 3
in match_chan ft1= euro56tg.log.tsy1.ntup nt1= 7 st1= 2u tt= 1
set scale tsys1 [2] min max 63.1 357.6
set scale tsys2 [2] min max 52.2 253.5
set scale tsys3 [2] min max  
 Tsys scale ymin 63.4 ymax 100 
in match_chan ft1= euro56tg.log.tsy1.ntup nt1= 11 st1= 6u tt= 1
set scale tsys1 [2] min max 63.1 357.6
set scale tsys2 [2] min max 52.2 253.5
set scale tsys3 [2] min max  
 Tsys scale ymin 63.8 ymax 100 
in match_chan ft1= euro56tg.log.tsy2.ntup nt1= 8 st1= 11u tt= 2
set scale tsys1 [2] min max 63.1 357.6
set scale tsys2 [2] min max 52.2 253.5
set scale tsys3 [2] min max  
 Tsys scale ymin 52.2 ymax 100