Starting generation of Calibration File 
FS version = 0009.0004.0006 
time_zero = 2372400 
Rack type is VLBA
Rack type is VLBA
Found #272 errors of type = ERROR 4f -503 Rack ID does not have at least two zero bits. 
Found #244 errors of type = ERROR qk -211 Tsys value for device ib overflowed or were less than zero. 
Found #244 errors of type = ERROR qk -211 Tsys value for device ic overflowed or were less than zero. 
Found #150 errors of type = ERROR ST  -23 portread_: timeout in acu-communication 
Found #120 errors of type = ERROR ST -111 acu_command: OFFS 
Found #30 errors of type = ERROR ST -122 acu_command: GETA 
Found #9 errors of type = ERROR qo -410 BEAM size must already be defined. 
Found #6 errors of type = ERROR bo -129 Error in new proc routine  stack is flushed. FMP  FFF 
Found #6 errors of type = ERROR ST   -2 portopen_: not able to open device 
Found #5 errors of type = ERROR qg -303 Track  4 parity errors exceed threshold. 
Found #5 errors of type = ERROR qg -303 Track 28 parity errors exceed threshold. 
Found #5 errors of type = ERROR qg -303 Track 18 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track 24 parity errors exceed threshold. 
Found #4 errors of type = ERROR qg -303 Track 20 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track  8 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 12 parity errors exceed threshold. 
Found #3 errors of type = ERROR qg -303 Track 22 parity errors exceed threshold. 
Found #3 errors of type = ERROR st -434 Error reading FM offset port. (OFF the 50 Ohm at counter!) 
Found #3 errors of type = ERROR qo -401 No default for BEAMx  until LO has  been setup. 
Found #3 errors of type = ERROR qg -303 Track 16 parity errors exceed threshold. 
Found #3 errors of type = ERROR ST -603 Weather station is sending parameters again. 
Found #3 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #3 errors of type = ERROR ST -601 Weather station didn't send parameters. 
Found #2 errors of type = ERROR qg -303 Track 27 parity errors exceed threshold. 
Found #2 errors of type = ERROR qk -211 Tsys value for device du overflowed or were less than zero. 
Found #2 errors of type = ERROR qz -414 Detector device 1 not one of ifa ... ifd or bbc1 ... bbc14. 
Found #2 errors of type = ERROR qg -303 Track 29 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -303 Track 30 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -303 Track 10 parity errors exceed threshold. 
Found #2 errors of type = ERROR 4f -501 Formatter was failing the synch test. 
Found #2 errors of type = ERROR qg -303 Track  6 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -303 Track 31 parity errors exceed threshold. 
Found #2 errors of type = ERROR qk -211 Tsys value for device eu overflowed or were less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device 2u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 8u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 6u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device ia overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device cu overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 1u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 4u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 3u overflowed or were less than zero. 
Found #1 errors of type = ERROR qk -211 Tsys value for device 5u overflowed or were less than zero. 
Found #1 errors of type = ERROR qg -303 Track 15 parity errors exceed threshold. 
Found #1 errors of type = ERROR sp   -1 Error in characters following a ! 
Found #1 errors of type = ERROR qa -201 Tape number must be 8 charaters. 
Found #1 errors of type = ERROR ma   -2 Illegal mode 
Found #1 errors of type = ERROR qk -211 Tsys value for device 7u overflowed or were less than zero. 
Found #1 errors of type = ERROR ch -233 rc tape drive should be moving and it isn't 
Found #1 errors of type = ERROR qk -211 Tsys value for device au overflowed or were less than zero. 
Found #1 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #1 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR qk -211 Tsys value for device bu overflowed or were less than zero. 
Found these BBCs: bbc02 bbc06 bbc11
NBBC: 3
Found these RX parameters: 00(BXFNT_) 01(IF_PLT) 03(DCAL_T)
RX1 min= 6.400 max= 16.10
RX2 min= 3.800 max= 16.80
RX3 min= 35.50 max= 42.60
Plotting 3 Tsys channels: 02 06 11
Tsysa values are: 1 2 3 etc
Tsysb values are: 9 10 11 etc
Tsysc values are:    etc
Tsysd values are:    etc
NTSYS: 3
in match_chan ft1= euro53tg.log.tsy1.ntup nt1= 7 st1= 2u tt= 1
set scale tsys1 [2] min max 56.2 9519.0
set scale tsys2 [2] min max 41.9 300.2
set scale tsys3 [2] min max  
 Tsys scale ymin 57.5 ymax 74.3 
in match_chan ft1= euro53tg.log.tsy1.ntup nt1= 11 st1= 6u tt= 1
set scale tsys1 [2] min max 56.2 9519.0
set scale tsys2 [2] min max 41.9 300.2
set scale tsys3 [2] min max  
 Tsys scale ymin 56.9 ymax 100 
in match_chan ft1= euro53tg.log.tsy2.ntup nt1= 8 st1= 11u tt= 2
set scale tsys1 [2] min max 56.2 9519.0
set scale tsys2 [2] min max 41.9 300.2
set scale tsys3 [2] min max  
 Tsys scale ymin 41.9 ymax 100