Starting generation of Calibration File 
FS version = 0009.0004.0013 
time_zero = 30128400 
Rack type is MK3/4
Found #119 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or were less than zero. 
Found #117 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #47 errors of type = ERROR qk -211 Tsys value for device vb overflowed or were less than zero. 
Found #15 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or were less than zero. 
Found #14 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #11 errors of type = ERROR qk -211 Tsys value for device va overflowed or were less than zero. 
Found #6 errors of type = ERROR qk -211 Tsys value for device vd overflowed or were less than zero. 
Found #5 errors of type = ERROR qg -303 Track 23 parity errors exceed threshold. 
Found #3 errors of type = ERROR st  -32 Limit on azimuth value. 
Found #2 errors of type = ERROR ch -309 vb alarm is on 
Found #2 errors of type = ERROR qg -303 Track 13 parity errors exceed threshold. 
Found #2 errors of type = ERROR qg -305 AUX data differs from expected value on track 23. 
Found #2 errors of type = ERROR ch -309 v3 alarm is on 
Found #1 errors of type = ERROR qg -303 Track  7 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -303 Track  8 parity errors exceed threshold. 
Found #1 errors of type = ERROR qg -305 AUX data differs from expected value on track  4. 
Found #1 errors of type = ERROR qg -305 AUX data differs from expected value on track 33. 
Found #1 errors of type = ERROR qg -305 AUX data differs from expected value on track  2. 
Found #1 errors of type = ERROR qa -202 Check label doesn't match.  Check it and try again. 
Found #1 errors of type = ERROR qg -303 Track 26 parity errors exceed threshold. 
Found #1 errors of type = ERROR st -105 [ANCOM] - Too many errors from LU      . 
Found #1 errors of type = ERROR qg -303 Track 14 parity errors exceed threshold. 
Found #1 errors of type = ERROR st -115 [ANTCN] - WARNING: X S paths are not in line. 
Found these BBCs: vc02 vc06 vc11
NBBC: 3
Found these  parameters:   
RX1 min= 100000 max= -1
RX2 min= 100000 max= -1
RX3 min= 100000 max= -1
Plotting 3 Tsys channels: 02 06 11
Tsys1 values are: 1 2 etc
Tsys2 values are: 9 10 etc
Tsys3 values are:   etc
NTSYS: 3
in match_chan ft1= c3006ma.log.tsy1.ntup nt1= 8 st1= v2 tt= 1
set scale tsys1 [2] min max 46.5 117.8
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 42.1 ymax 130.6 
in match_chan ft1= c3006ma.log.tsy1.ntup nt1= 12 st1= v6 tt= 1
set scale tsys1 [2] min max 46.5 117.8
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 47.4 ymax 147.8 
in match_chan ft1= c3006ma.log.tsy2.ntup nt1= 9 st1= v11 tt= 2
set scale tsys1 [2] min max 46.5 117.8
set scale tsys2 [2] min max -5 305
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305